Tuesday, November 23, 2010

G.T.POWER A607 MAX 7A 80W LiPo RC Digital Charger



Specifications

Operating Voltage Range: DC 10 - 18V

Circuit Power: Max. 80W for charging, Max. 5W for discharging

Charge Current Range: 0.1 - 7.0A

Discharge Current Range: 0.1 - 1.0A

Current drain for balancing Li-po: 300mAh/cell

NiCd/NiMH battery cell count: 1 - 15 Cells

Lithium Battery Cell Count: 1 - 6 Series

Pb Battery Voltage: 2 to 20V

Dimensions: 135mm x 100mm x 40mm

Packet Includes: Multifuctional Connector

Features

Optimized operating software

When charging or discharging, It has an `AUTO` function that sets the feeding current automatically. Especially for Lithium batteries, it can prevent the over-charging can lead to an explosion by users fault. Every program in the unit is controlled with mutual links and communication for every possible error so it introduces a maximum safety. These can be set at users option.



Special recharge plugsport for receiver, transmitter and igniter charger. And for frequently used charger port such as multi purpose crocodile pin etc.



It provides most convenient balance charge port for Lithium batteries, with separated 3,4,5,6 charge port, and external reverse connector.



High-power and high-performance circuit

It employs the circuit that has maximum output power of 80W. As a result it can charge or discharge up to 15 cells of NiCd/NiMH and 6 series of Lithium batteries with maximum current of 7.0A. Furthermore the cooling system is so efficient that can hold such a power without any trouble of running the CUP or the operating program.



Individual voltage balancer for Lithium batteries inside

It has an individual-cell-voltage balancer inside. This does not require any extra balancer separately when charging Lithium batteries (Lilo/LiPO/LiFe) for cell voltage balancing.



Balance individual cells on discharge

It also can monitor and balance individual cells of the Lithium battery pack during the discharge process. If the voltage of any one cell varies abnormally, the process will be stopped with the error message.



Accept various types of Lithium battery

It can accept three types of Lithium batteries - Lilo, LiPo and LiFe. They have different characteristics by their chemistry. You can select any one of them that you are going to process before the job. For their specifications, refer `Warnings and safety notes` section.





Lithium battery `Fast` and `Storage` mode

You can charge Lithium battery for special purposes. `Fast` charge reduces the charging time of Lithium battery and `storage` mode controls the final voltage of the battery to be suit for long time storage.



Maximum safety

Delta-peak sensitivity: The automatic charge termination program works on the principle of the Delta-peak voltage detection. (NiCd/NiMH)



Auto-charge current limit: When charging NiCd or NiMH at `AUTO` current mode, you can set the upper limit of change current to avoid from high current charging. This is very useful when charging the low impedance and small capacity NiMH battery in `AUTO` mode.



Capacity limit: The changing capacity always calculated by multiple of the charging current and time. If the charging capacity exceeds the limit the process will be terminated automatically when you set the maximum value.



Processing time limit: you can also restrain the maximum process time to prevent form any possible defect.



Input power monitor: To protect the car battery using as input power from being damaged the voltage of it always monitored. If it drops below the lower limit the process will be ended automatically.



Automatic cooling fan: The electric cooling fan comes into action automatically only when the internal temperature of the unit is raised.



Data store / load

For users convenience it can store maximum 5 data of different batteries. You can establish the data contains program setting of the battery to charge or discharge continually. These data can be called out at any time you need and the process can be executed without program setting.



Cyclic charging / discharging

Perform 1 to 5 cycles of charge>discharge or discharge>charge continually for battery refreshing and balancing.

No comments:

Post a Comment